MDC 16650 SHO FLASHLIGHT
MDC 16650 SHO FLASHLIGHT
MDC 16650 SHO FLASHLIGHT
MDC 16650 SHO FLASHLIGHT
MDC 16650 SHO FLASHLIGHT
MDC 16650 SHO FLASHLIGHT

Malkoff Devices

MDC 16650 SHO FLASHLIGHT

$165.99 $172.98
Choose Head:

Choose Head
Choose Pocket Clip:

Choose Pocket Clip
Quantity:

DESCRIPTION:

Malkoff MDC 16650 SHO (Single High Output) Flashlight with various head options such as our E2, E2 Super V3, E2HTV3, or E2XTV3.

The Flashlight consists of a MDC 16650 Handheld Body and one of our MDC heads of the "E2" variety. The body is one piece with a McClicky Switch and Pocket Clip of your choosing Installed. The options for the Pocket Clip may be chosen with the buttons above. It DOES NOT have a removable tailcap. It is constructed of 6061 T6 Aluminum and is HA Black Type III Hard Anodized. 

The body is designed for a single protected 16650 rechargeable battery. We encourage the use of protected batteries for overall safety.

 HEAD CANDELA LUMENS BATTERY(S)/MAH DRAW
        E2HTV3            (throw and good spill)

33K

40K**

~850 

~1050-1200**

2x CR123 ~1400mah draw

1x 16650*~ 2800mah draw
        E2XTV3                 (more throw and less spill)

50K

65K**

~800

~1050-1150**

2x CR123 ~1400mah draw

1x 16650*~ 2800mah draw
           E2SV3 (Super)            (combination beam -  bright floody, limited throw) 12K

~900

~1100*

2x CR123 ~1400mah draw

1x 16650*~ 2800mah draw
              E2/M600                (combination beam, floody, limited throw) 6.5K ~450

2x CR123 ~800mah draw

1x 16650 ~ 1100mah draw

*Below 3.6 volts the flashlight will slowly taper in output. Low Voltage Protection (fast taper) doesn't start until 3 volts. Below 2.7 volts the flashlight will turn itself off. The use of an unprotected cell entails additional risks. 

**Actual highest output is dependent on the internal resistance of the battery. The use of an unprotected cell entails additional risks. 

TITANIUM POCKET CLIP OPTION

The optional Titanium Deep Carry MDC Pocket Clips are custom designed and manufactured by LynchNW exclusively for the Malkoff Devices line of MDC Pocket Lights. They are made of Grade 5 6AL-4V Titanium with a Stone Washed Finish. These pocket clips will prevent tail-standing the light. Clip description HERE.

STAINLESS-STEEL BEZEL OPTION

We have stainless-steel(SS) bezels for the E2/M600, E2SV3 (Super), and E2HTV3. The full descriptions can be found in the following links:

E2/M600 Bezels: Standard sold HERE. Crenelated sold HERE.

E2HTV3 and E2SV3 Bezel sold HERE.

This item is Covered by Our Lifetime Warranty. 

Made in the USA. Some parts not domestically sourced.

Battery Warnings For Rechargeable Li-ion Batteries:

- Do Not over-discharge/overcharge

- Please recharge drained batteries ASAP

- Do Not short circuit

- Do Not dispose of in fire

- Do Not expose to extreme heat or water

- Please be familiar with the handling of rechargeable Lithium-ion batteries prior to their purchase

Battery Warnings:

Lithium Primary and Li-ion Rechargeable Batteries are Inherently Volatile and Dangerous to Store and Use. All Lithium Batteries Introduce the Risk of Fire, Burns, and Explosions. You Assume the Responsibility of Educating Yourself About Their Use and Storage Before Purchase! If You are Uncomfortable With This, Do Not Purchase this Light!

The input voltage is 3.7 - 9 volts.  Input voltages of more 9 volts may destroy this flashlight.

The Flashlight is protected against reverse polarity.

WARNING: This light is capable of causing eye damage at close range. Please use the light responsibly!!!